#231
|
|||
|
|||
I skipped all audio content
Sorry I can't be of any help as I use a Bose Companion 5 USB speaker set and so have audio disabled in my BIOS and skip all those portions of the directions. Best of luck in your search to get it working.
|
#232
|
|||
|
|||
CMOS - Corrupt
What is the easiest way to fix the CMOS Reset error I get every time my computer restarts? I am using the DSDT downloaded in the ES2L Kit. Everything else works like a charm on my G31m-es2l. I've tried the cmos corrupt fix in the es2l folder. How did everyone else fix theirs?
G31m-es2l Rev 2.0 9600GT 512 Snow Leopard 6.1 |
#233
|
|||
|
|||
verifying DMI pool data
I followed the guide (thanks for all your work on this!) and was installing SL when the machine rebooted, and now all I get is "verifying DMI pool data." i've re-formatted my thumb drive, did the entire process over, and still, "verifying DMI pool data." I have v2 of the board, and am trying to use onboard graphics. Is that my issue?
|
#234
|
|||
|
|||
try this......
Search es2l on these boards.....guide under Voyn1x at the end shows Alc883.zip
I did use Kext Helper 0.7 to install both.............got from weaksauce leopard soup es2l guide and folder. AppleAzaliaAudio: Version: 1.0.0 Last Modified: 10/21/09 8:04 PM Get Info String: 1.0.0, Copyright Apple Computer, Inc. 2005 Kind: Intel Architectures: i386 64-Bit (Intel): No Location: /System/Library/Extensions/AppleAzaliaAudio.kext Kext Version: 1.0.0d1 Load Address: 0x5b6d4000 Valid: Yes Authentic: Yes Dependencies: Satisfied AppleAzaliaController: Version: 1.0.0 Last Modified: 10/21/09 8:04 PM Get Info String: 1.0.0, Copyright Apple Computer, Inc. 2005 Kind: Intel Architectures: i386 64-Bit (Intel): No Location: /System/Library/Extensions/AppleAzaliaAudio.kext/Contents/PlugIns/AppleAzaliaController.kext Kext Version: 1.0.0d1 Load Address: 0x5b528000 Valid: Yes Authentic: Yes Dependencies: Satisfied Had to install pci etherent card.........trendnet Type: Ethernet Controller Bus: PCI Vendor ID: 0x10ec Device ID: 0x8169 Subsystem Vendor ID: 0x10ec Subsystem ID: 0x8169 Revision ID: 0x0010 disable 'on board lan' Last edited by 353inf; 10-27-2009 at 10:48 PM. |
#235
|
|||
|
|||
Help with Audio no Work
Audio no work in 32bit or 64bit
please some help ACL883 |
#236
|
|||
|
|||
No Sound
Ditto here on sound.
Nothing doing. V2 using firmware from Gigabyte FF, FE did not work either. Tried Voodo, Taruga 64 Sound stuff is scattered all over the net but nothing concrete. Thanks for this thread it is lengthy but you gain some knowledge from it. |
#237
|
|||
|
|||
Thanks to this thread and all the great contributions I have my ES2L R2.0 FC BIOS, E6300 OC'ed to 3.4GHz, 4GB RAM, 9500GT 512MB, PCI TrendNet Ethernet (due to no driver for the R2.0 onboard Ethernet), and PCI Firewire all working great! Everything I have tried so far, including audio and sleep works. I haven't tried automatic sleep but manual works fine and I never used automatic sleep in the past.
I used Conti's myHack 1.0 RC4 to install. Then I extracted my DSDT and compiled and found some errors. I fixed those using the DSDTSE Fixes Menu and then changed the RTC section as sk1nhd33t instructed and added the Method DTGP. For audio I used only the LegacyALC883.kext provided in the ES2L Kit sk1nhd33t linked in the first post of this thread and then modified my DSDT to remove the "Sound AZALIA" section and replace it with coconup's DSDT HDEF code. I also added the DSDT USB sleep fix and System Profiler now shows all my USB 2.0 Buses as Built-in. For those that may be interested I have attached my dsdt.dst. Thanks to all those who have contributed. Britney |
#238
|
|||
|
|||
This guide has been a life saver, I bought Snow Leopard thinking I could just install like Leopard and everything would work. This guide actually makes the install EASIER than Leopard. Thanks much for your work on this.
Well, I was able to get everything but the sound to work so instead of trying this that and the other thing, I just bought Creative's Xmod USB sound adapter for around $20 bucks on Amazon and now I have sound! |
#239
|
|||
|
|||
Quote:
|
#240
|
|||
|
|||
Quote:
For the overclock all I did was set the cpu multiplier to 10.5 and the front side bus to 325MHz. I had the front side bus at 333MHz but after the machine would sleep it would be awake for about 10 mins and would then kernel panic. Backing off the front side bus to 325MHz seems to have fixed that. Britney 💡 Deploy cloud instances seamlessly on DigitalOcean. Free credits ($100) for InfMac readers. |