Hello Drago

I want to thank you for your great Job.

My Dell:
D830
NividiaQuadroNVS140m
Ethernet-Broadcom
Intel Wireless 3945 ABG
Audio Intel 82801

Your guide for the installation is really good.
Everthing works fine.

My problem was, that my extern monitor don't accept the resolution of my Dell, and at the installation, the Nvidia Card didn't work.
Because of that i had to made a install with bootoption "-x" before installationprocess start (step 4).
After the installation i installed a linux distribution (mint) and made a partition with hfs.
Now i downloaded the 10.6.4 Combo Update and Multibeast and save it on the hfs partition.
After that, i made a reeboot with iboot cd and option "-x" again and installed the way you have described (step 9).

Thanks for your great job!

Hi. I am going to try to install OSX on my Dell D630. Never tried this before. I am currently downloading iATKOS_v7 from tpb. My D630 has a C2D T7250, GM965 chipset, Broadcom wifi, and Mobile Intel 965 graphics. I have the A17 BIOS installed. The only changes I made were SATA to AHCI.

Is there anything else I will need? Do I just boot to the iATKOS dvd? I also have Boot 132 burned to a cd. Will I need that? Thanks guys.

Download finished. Checked the MD5 Checksum and it looked good. Booted iATKOS_v7 to my D630, hit F8 and used -v and the screen froze here...

http://img682.imageshack.us/img682/7469/photo3vf.jpg

So then I rebooted and tried -v cpus=1 and the screen froze here...

http://img837.imageshack.us/img837/3680/photo4r.jpg

Any ideas on what I should try next? Thanks.

Well, I gave up on iATKOS_v7. I downloaded iATKOS S3 v2 and it seems to be working better. I can now get to the install screen and I start the install but it crashes and asks me to reboot. Any ideas?

I would advise you to use the Empire-EFI method: boot with the Empire-EFI CD-ROM and install from original Mac OSX 10.6 DVD. Then, for optimal graphics support (see earlier post), install Chameleon 2.0 RC4. Finally, install the DELL kext pack as prepared and made available in this thread and you should be up and running!

Good luck!

Just upgraded to Mac OSX 10.6.4 without any problem! All hardware functions are fully operational (including the WiFi <= see earlier post). Only remaining problem is still Shut down / Restart...

Thanks Adrenaline1965. I'll give that a try and report back. I have an OSX 10.6.3 disk. Will that work with Empire EFI?

I lose audio when I go to 10.6.4. I am currently running 10.6.2, RC4, and the original dell kext pack, plus most current sleep enabler. Any ideas?

---

Gigabyte GA-G31M-ES2L • Q9400 Core 2 Quad overclocked to 3.19 GHz • Zotac 9400GT-• 4 GB ram • SL 10.6.2 • VMWare Fusion
Dell D630 with Intel X3100 • [email protected] GHz • 2 GB ram • SL 10.6.2 • Crossover 9.0
Dell Mini 10v • Dual boot Win XP and SL 10.6.2

I did a fresh install using the empire legacy boot disk, then installed 10.6.0 from a retail disk, upgraded to 10.6.4, installed chameleon and user dsdt via multibeast. (using the dsdt.aml and installing the kexts from howorang's pack.) Everything works except sleep. I've never been able to get sleep to work on any version of os x on my d630. I must have installed it a zillion times. I have i5 and i7 gigabyte desktop machines that work flawlessly---I used the IBOOT Supported disk and it's pretty automagic. I noticed that with an extra terminal attached to the d630 the lcd goes blank but the other monitor stays on when you close the clamshell of the laptop. Does anybody have x3100 graphics on a d630 and sleep works? It's a dealbreaker for me.

For audio I'm currently using VoodooHDA.kext. Works fine for me (previously tried patched AppleHDA.kext and legacySTAC9205.kext but these did not give me any satisfaction)